/* Contents of format file "ROMAP_RAWHK.FMT" (Uncalibrated HK data) */
OBJECT = COLUMN
NAME = "UTC"
DATA_TYPE = TIME
START_BYTE = 1
BYTES = 23
DESCRIPTION = "This column represents the UTC
Of the magnetic field vector in PDS standard format
YYYY-MM-DDThh:mm:ss.sss"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "OBT"
DATA_TYPE = ASCII_REAL
START_BYTE = 25
BYTES = 15
UNIT = SECOND
FORMAT = "F15.5"
DESCRIPTION = "ROMAP 4 bytes counter representing the measurement
time synchronized with Lander On Board Time.
The time resolution is 0.03125 s"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "CONTROLLER STATUS"
DATA_TYPE = CHARACTER
START_BYTE = 42
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = " Controller Status Bits in Hexadecimal Format :
Bit Description
0 Status flag : Instrument Mode was loaded
at power-up from TC-Buffer
1 Status flag : MAG setting was loaded from
TC-Buffer
3 Error flag : read TC-Buffer error at power-up
4 Error flag : write BRAM error; cleared after
successfully writing BRAM
5 Error flag : TC-Buffer content error
(illegal checksum)
6 Error flag : SPM Ion 1 counter overflow occurred
(cleared after displaying SPM
overflow error flag in HK data)
7 Error flag : SPM Ion 2 counter overflow occurred
(cleared after displaying SPM
overflow errorflag in HK data)
8 Error flag : SPM Electron counter overflow
occurred (cleared after displaying
SPM overflow error flag in HK data)
9 Status flag : Penning pressure sensor on/off
10 Status flag : Pirani pressure sensor on/off
11 Status flag : DUMMY FPGA output on/off
12..13 Not used
14..15 Status flags: I0, I1 identify instrument mode
If one of the bits 0 .. 5 is set once, it stays active
until the instrument is switched off."
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "LAST RECEIVED TC (WORD 1)"
DATA_TYPE = CHARACTER
START_BYTE = 49
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = "Last received TC (word 1) in Hexadecimal Format"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "LAST RECEIVED TC (WORD 2)"
DATA_TYPE = CHARACTER
START_BYTE = 56
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = "Last received TC (word 2 )in Hexadecimal Format"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "POWER CONSUMPTION"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 62
BYTES = 6
FORMAT = "I6"
UNIT = "ADC_COUNTS"
DESCRIPTION = "Overall instrument power consumption
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "+5V CURRENT"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 69
BYTES = 6
FORMAT = "I6"
UNIT = "ADC_COUNTS"
DESCRIPTION = "+5V current
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "-5V CURRENT"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 76
BYTES = 6
FORMAT = "I6"
UNIT = "ADC_COUNTS"
DESCRIPTION = "-5V current
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "ELECTRONICS TEMPERATURE"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 83
BYTES = 6
FORMAT = "I6"
UNIT = "ADC_COUNTS"
DESCRIPTION = "electronics temperature
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "+28V CURRENT"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 90
BYTES = 6
FORMAT = "I6"
UNIT = "ADC_COUNTS"
DESCRIPTION = "+28V current
"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SPM HV STATUS 1"
DATA_TYPE = CHARACTER
START_BYTE = 98
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = "SPM HV status 1 in Hexadecimal Format"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SPM HV STATUS 2"
DATA_TYPE = CHARACTER
START_BYTE = 105
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = "SPM HV status 2 in Hexadecimal Format"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SPM HV STATUS 3"
DATA_TYPE = CHARACTER
START_BYTE = 112
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = "SPM HV status 3 in Hexadecimal Format"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SPM HV STATUS 4"
DATA_TYPE = CHARACTER
START_BYTE = 119
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = "SPM HV status 4 in Hexadecimal Format"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "PENNING PRESSURE"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 125
BYTES = 6
FORMAT = "I6"
UNIT = "ADC_COUNTS"
DESCRIPTION = "Penning pressure"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "PIRANI PRESSURE"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 132
BYTES = 6
FORMAT = "I6"
UNIT = "ADC_COUNTS"
DESCRIPTION = "Pirani pressure"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "PROM CHECKSUM"
DATA_TYPE = CHARACTER
START_BYTE = 140
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = "PROM checksum (computed at power-up)
in Hexadecimal Format"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "INSTRUMENT ERROR FLAGS"
DATA_TYPE = CHARACTER
START_BYTE = 147
BYTES = 4
FORMAT = "A4"
UNIT = "N/A"
DESCRIPTION = " Instrument Error Flags in Hexadecimal Format :
Bit Description
0 Command overflow (a TC was received before the
former was processed)
1 CDMS illegal word count
2 CDMS message error
3 General CDMS receiving error
4 General CDMS transmission error
5 Wrong telecommand received
6 CDMS request overflow (a CDMS request occurs
before the former was processed)
7 Frame buffer overflow
8 MAG vector sampling overflow
9 CDMS error code word received
10 CDMS checksum error
11 checksum error in received CDMS SST word
12 SPM counter overflow
13 ADC sampling overflow
14 SPM transmission overflow
15 SPM setup error"
END_OBJECT = COLUMN