/* PP AMTEST2 sensor settings and on-board evaluation results */
/* Version 2, 2015-11-11 */
OBJECT = COLUMN
NAME = "SESAME_SEQ_ID"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 1
BYTES = 6
UNIT = "N/A"
FORMAT = "I6"
DESCRIPTION = "Sequence ID in the current data file"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "UTC"
DATA_TYPE = TIME
START_BYTE = 8
BYTES = 23
DESCRIPTION = "Measurement start time (UTC in PDS standard
format YYYY-MM-DDThh:mm:ss.sss)"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SESAME_LOCAL_TIME"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 32
BYTES = 15
FORMAT = "I15"
DESCRIPTION = "Measurement start time. SESAME local time
(SLT) runs with a resolution of 1/32 seconds.
SLT represents the least significant 32 bits
of LOBT. The most significant 5 bits are in
CDMS RSST (see SESAME Ready Message)"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SENSOR_SETTINGS_CMD"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 48
BYTES = 7
UNIT = "N/A"
DESCRIPTION = "Commanded (echoed) electrode combination
as 3-digit hexadecimal value 16#abi#
with the following meaning:
a: electrode connected to the TX A output.
Possible values:
0 [none],
1 [+X leg],
2 [MUPUS PEN]
b: electrode connected to the TX B output.
Possible values:
0 [none],
2 [MUPUS PEN],
3 [APXS]
i: input channel
Possible values:
0 [potential difference]
1 [current at +X leg]
2 [current at MUPUS PEN]
3 [current at APXS]
4 [direct measurement at +Y foot]
5 [direct measurement at -Y foot]
6 [reference voltage -2.5 V]
7 [reference voltage +2.5 V] "
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TX_FREQ"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 56
BYTES = 5
UNIT = "HERTZ"
FORMAT = "I5"
DESCRIPTION = "Tx frequency "
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TX/RX_WAVES"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 62
BYTES = 3
UNIT = "N/A"
FORMAT = "I3"
DESCRIPTION = "Number of Tx/Rx waves "
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "PTS_PER_WAVE"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 66
BYTES = 3
UNIT = "N/A"
FORMAT = "I3"
DESCRIPTION = "Points per wave "
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TX_OUT_DAMPING"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 70
BYTES = 1
UNIT = "N/A"
FORMAT = "I1"
DESCRIPTION = "TX Voltage Amplitude Reduction. The possible values are:
0 maximum amplitude.
1 half amplitude.
2 quarter amplitude.
3 1/8 amplitude.
4 1/16 amplitude."
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "ADC_DIV"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 72
BYTES = 4
UNIT = "N/A"
FORMAT = "I4"
DESCRIPTION = "Sampling frequency is generated as 5 MHz / this parameter"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "ADC_ADDR"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 77
BYTES = 5
UNIT = "N/A"
FORMAT = "I5"
MISSING_CONSTANT = 99999
DESCRIPTION = "Adjusted last address in PP memory "
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "DAC_DIV"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 83
BYTES = 4
UNIT = "N/A"
FORMAT = "I4"
DESCRIPTION = "Tx voltage update frequency is 5 MHz / this parameter"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "DAC_ADDR"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 88
BYTES = 3
UNIT = "N/A"
FORMAT = "I3"
DESCRIPTION = "Last used address in DAC table"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "ERROR_CODE"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 92
BYTES = 8
MISSING_CONSTANT = 16#0000#
DESCRIPTION = "Active mode results as hexa 16#xxxx#
The possible values are:
8001 Invalid register address.
8002 Error verifying register write.
8004 Error accessing power register.
8008 MUX setting not allowed.
8010 Error accessing PP RAM.
8020 Tried to start measurement but a measurement
is already running.
0040 Error during writing to instrument.
0080 Error during reading from instrument.
0100 Error using ADC of C-DPU.
0200 Error during DAC table generation.
0400 Calculated number of samples > N_SAMP_MAX.
8800 C-DPU memory exhausted.
9000 Measurement time out.
2000 Invalid command parameter.
8000 Flag indicates fatal error. "
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "QUAL_FLAG_CL"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 101
BYTES = 1
FORMAT = "I1"
UNIT = "N/A"
DESCRIPTION = "PP quality flags. The possible values are:
0 OK
1 at least one sample equals 0 in
current (transmitter) time series"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "QUAL_FLAG_VH"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 103
BYTES = 1
FORMAT = "I1"
UNIT = "N/A"
DESCRIPTION = "PP quality flags. The possible values are:
0 OK
1 at least one sample equals 255 in
voltage (receiver) time series"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "QUAL_FLAG_VL"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 105
BYTES = 1
FORMAT = "I1"
UNIT = "N/A"
DESCRIPTION = "PP quality flags. The possible values are:
0 OK
1 at least one sample equals 0 in
voltage (receiver) time series"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "POINTS_PER_WAVE"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 107
BYTES = 3
UNIT = "N/A"
FORMAT = "I3"
MISSING_CONSTANT = 999
DESCRIPTION = "Number of points per wave used by receiver"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "PHASE"
DATA_TYPE = ASCII_REAL
START_BYTE = 111
BYTES = 8
UNIT = "DEGREE"
FORMAT = "F8.4"
DESCRIPTION = "Phase difference potential-current"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "CURRENT_AMPLITUDE"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 120
BYTES = 3
UNIT = "N/A"
FORMAT = "I3"
DESCRIPTION = "Scaling as raw data without offset
128 = max. ADC value for current"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "VOLTAGE_AMPLITUDE"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 124
BYTES = 3
UNIT = "N/A"
FORMAT = "I3"
DESCRIPTION = "Scaling as raw data without offset
128 = max. ADC value for Rx voltage diff."
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "MATH_ERR"
DATA_TYPE = CHARACTER
START_BYTE = 128
BYTES = 8
MISSING_CONSTANT = 16#0000#
DESCRIPTION = "Hex value as 16#xxxx#
0001 Reduce: number of vector elements odd or less
than 2; fatal.
0002 Expand: less than four elements in input
vector; fatal.
0004 Too much data for analysis; truncating.
0008 Too few data for analysis; padding with 128
0010 Used number of waves is not a power of 2;
truncated.
0020 Not the expected number of elements in
filtered arrays; fatal.
0040 Argument for sine_table() not in valid range
0<= deg2 <=720.
0080 Overflow in divsin() or result inexact.
0100 Too few data for trimmed mean calculation;
regular mean used.
0200 No data for warr.mean; particular: analysis
yields no data.
0400 Passive mode: not enough data in bin.
0800 Not enough memory for data reduction."
END_OBJECT = COLUMN