OBJECT = COLUMN
NAME = "TABLE_TIME_UTC"
DATA_TYPE = TIME
START_BYTE = 1
BYTES = 23
UNIT = "N/A"
DESCRIPTION = "UTC Time in PDS standard format
YYYY-MM-DDThh:mm:ss.sss"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TABLE_TIME_OOBT"
DATA_TYPE = CHARACTER
START_BYTE = 26
BYTES = 17
MISSING_CONSTANT = " 9/9999999.99999"
DESCRIPTION = "Orbiter On Board Time
OOBT is represented as:
Reset number (integer starting at 1) / seconds.
Reset number 1 starts at 2003-01-01T00:00:00 UTC
The time resolution is 1/65536 s"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TABLE_TYPE"
DATA_TYPE = CHARACTER
START_BYTE = 46
BYTES = 3
DESCRIPTION = "Possible values:
TBL for Configuration table containing the operational
parameters which can be modified in the onboard software
CTL for Control sequence, used to get a detailed status
of the experiment (also containing the configuration table"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TABLE_NUMBER"
DATA_TYPE = CHARACTER
START_BYTE = 52
BYTES = 12
FORMAT = "N/A"
DESCRIPTION = "Table number, given in the form x/y , where:
x is the current number of the table in the PDS dataset
y is the maximum number of tables found in the PDS dataset"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TABLE_BYTES_HEX"
DATA_TYPE = CHARACTER
START_BYTE = 67
BYTES = 17
DESCRIPTION = "Configuration table, containing all the operational
parameters, given as 6 bytes in Hexadecimal format
(one link-packet between PIU and RPC-MIP), separated by
a blank character.
The description is given below :
byte 0
bits 4,3 : Interference frequency #1
byte 1
bits 4,3 : Interference frequency #2
byte 2
bits 4,3 : Interference frequency #3
byte 3
bits 7,6 : Transmission_level
bits 5,4 : Transmitter_odd_sweeps
bits 3,2 : Transmitter_even_sweeps
bits 1,0 : Extremum_threshold
byte 4
bits 7,6,5 : Sweep_mode_bandwidth
bits 4,3,2 : Survey_mode_bandwidth
bit 1 : Ampl_pas
bit 0 : Autoloop
byte 5
bit 7 : Watchdog
bits 6,5,4 : Science_sequence_number
bit 3 : LDL_type
bit 2 : Mode
bits 1,0 : TM_rate"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "INTERF_FREQ1"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 86
BYTES = 4
UNIT = KILOHERTZ
FORMAT = "I4"
DESCRIPTION = "Interference frequency number 1
i.e. frequency to be ignored during the on-boar
extremum detection the active modes"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "INTERF_FREQ2"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 91
BYTES = 4
UNIT = KILOHERTZ
FORMAT = "I4"
DESCRIPTION = "Interference frequency number 2
i.e. frequency to be ignored during the on-boar
extremum detection the active modes"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "INTERF_FREQ3"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 96
BYTES = 4
UNIT = KILOHERTZ
FORMAT = "I4"
DESCRIPTION = "Interference frequency number 3
i.e. frequency to be ignored during the on-boar
extremum detection the active modes"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TRANSMISSION_LEVEL"
DATA_TYPE = ASCII_REAL
START_BYTE = 101
BYTES = 5
UNIT = "N/A"
FORMAT = "F5.3"
DESCRIPTION = "Level of the transmitted signal
Possible values: {1.000, 0.500, 0.250, 0.125}
1.000 for full level,
(156 mV RMS in MIP mode, 30 V RMS in LDL mode)
0.500 for nominal level,
(78 mV RMS in MIP mode, 15 V RMS in LDL mode)
0.250 for low level,
(39 mV RMS in MIP mode, 7.5 V RMS in LDL mode)
0.125 for minimum level,
(19.5 mV RMS in MIP mode, 3.75 V RMS in LDL mode) "
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TRANSMISSION_ODD"
DATA_TYPE = CHARACTER
START_BYTE = 108
BYTES = 29
UNIT = "N/A"
DESCRIPTION = "Transmitter configuration for odd sweeps (1, 3, ...)
Possible values:
mono with E1
mono with E2
stereo with E1-E2 phased
stereo with E1-E2 anti-phased"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TRANSMISSION_EVEN"
DATA_TYPE = CHARACTER
START_BYTE = 140
BYTES = 29
UNIT = "N/A"
DESCRIPTION = "Transmitter configuration for even sweeps (2, 4, ...)
Possible values:
mono with E1
mono with E2
stereo with E1-E2 phased
stereo with E1-E2 anti-phased"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "MODE"
DATA_TYPE = CHARACTER
START_BYTE = 172
BYTES = 9
UNIT = "N/A"
DESCRIPTION = "SDL/LDL transmitter configuration:
Possible values: {MIP alone, LDL mode}
MIP alone for SDL
LDL mode for LDL"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "AUTOLOOP"
DATA_TYPE = CHARACTER
START_BYTE = 184
BYTES = 16
UNIT = "N/A"
DESCRIPTION = "Autoloop : an auto-loop can be set between emission
and reception
Possible values:
MIP with sensor
MIP auto-loop ON"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "AMPL_PAS"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 202
BYTES = 1
UNIT = DECIBEL
FORMAT = "I1"
DESCRIPTION = "Coding level for the power spectrum in Passive mode
0 dB = 0.6 microV*Hz**-0.5
Possible values: {2, 4}
2, for 16 values from 0 to 30 dB
4, for 16 values from 0 to 60 dB"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "EXT_THRESHOLD"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 204
BYTES = 1
UNIT = DECIBEL
FORMAT = "I1"
DESCRIPTION = "Amplitude threshold for the extremum detection
0 dB = 0.6 microV*Hz**-0.5
Possible values:
1
2
4
8"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SURVEY_BAND"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 206
BYTES = 1
UNIT = "N/A"
FORMAT = "I1"
DESCRIPTION = "Frequency table used in Survey modes
Possible values: 0 to 7
Frequency tables are described below, with details on
bandwidth resolution number of steps
Table #0 (nominal) from 28 kHz to 3472 kHz, decomposed as:
28 - 224 kHz 7 kHz 29
238 - 448 kHz 14 kHz 16
476 - 896 kHz 28 kHz 16
952 - 1792 kHz 56 kHz 16
1904 - 3472 kHz 112 kHz 15
Table #1 from 28 kHz to 665 kHz
28 - 665 kHz 7 kHz 92
Table #2 from 259 kHz to 896 kHz
259 - 896 kHz 7 kHz 92
Table #3 from 518 kHz to 1792 kHz
518 - 1792 kHz 14 kHz 92
Table #4 from 924 kHz to 3472 kHz
924 - 3472 kHz 28 kHz 92
Table #5 from 357 kHz to 987 kHz, decomposed as:
28 - 343 kHz 7 kHz 46
357 - 987 kHz 14 kHz 46
Table #6 from 28 kHz to 1582 kHz, decomposed as:
28 - 224 kHz 7 kHz 29
238 - 630 kHz 14 kHz 29
658 - 1582 kHz 28 kHz 34
Table #7 from 266 kHz to 2184 kHz, decomposed as:
266 - 896 kHz 14 kHz 46
924 - 2184 kHz 28 kHz 46"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SWEEP_BAND"
DATA_TYPE = ASCII_INTEGER
START_BYTE = 208
BYTES = 1
UNIT = "N/A"
FORMAT = "I1"
DESCRIPTION = "Frequency table used in Sweep modes
Possible values: 0 to 7
Frequency tables are described below, with details on
bandwidth resolution number of steps
Table #0 (nominal) from 28 kHz to 3472 kHz, decomposed as:
28 - 224 kHz 7 kHz 29
238 - 448 kHz 14 kHz 16
476 - 896 kHz 28 kHz 16
952 - 1792 kHz 56 kHz 16
1904 - 3472 kHz 112 kHz 15
Table #1 from 28 kHz to 665 kHz
28 - 665 kHz 7 kHz 92
Table #2 from 259 kHz to 896 kHz
259 - 896 kHz 7 kHz 92
Table #3 from 518 kHz to 1792 kHz
518 - 1792 kHz 14 kHz 92
Table #4 from 924 kHz to 3472 kHz
924 - 3472 kHz 28 kHz 92
Table #5 from 357 kHz to 987 kHz, decomposed as:
28 - 343 kHz 7 kHz 46
357 - 987 kHz 14 kHz 46
Table #6 from 28 kHz to 1582 kHz, decomposed as:
28 - 224 kHz 7 kHz 29
238 - 630 kHz 14 kHz 29
658 - 1582 kHz 28 kHz 34
Table #7 from 266 kHz to 2184 kHz, decomposed as:
266 - 896 kHz 14 kHz 46
924 - 2184 kHz 28 kHz 46"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "WATCHDOG"
DATA_TYPE = CHARACTER
START_BYTE = 211
BYTES = 12
UNIT = "N/A"
DESCRIPTION = "MIP watchdog status
Possible values:
watchdog on
watchdog off"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "TM_RATE"
DATA_TYPE = CHARACTER
START_BYTE = 226
BYTES = 12
UNIT = "N/A"
DESCRIPTION = "Telemetry rate
Possible values:
minimum rate
normal rate
burst rate"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "SEQUENCE_NR"
DATA_TYPE = CHARACTER
START_BYTE = 241
BYTES = 27
UNIT = "N/A"
DESCRIPTION = "MIP sequence number
Possible values:
nominal sequence
complementary sequence nr 1
complementary sequence nr 2
complementary sequence nr 3
complementary sequence nr 4
complementary sequence nr 5
complementary sequence nr 6
complementary sequence nr 7"
END_OBJECT = COLUMN
OBJECT = COLUMN
NAME = "LDL_TYPE"
DATA_TYPE = CHARACTER
START_BYTE = 271
BYTES = 10
UNIT = "N/A"
DESCRIPTION = "LDL type
Possible values:
normal LDL
mixed LDL"
END_OBJECT = COLUMN